上海家用商用净水器_净水器免费试用_净水器租赁-上海浩泽净水器

网站首页 > 新闻资讯 > 公司动态

商业净水器的安装维护工艺你了解吗?

1、 位置的选择:商用净水器一般安装在商务、公共场所、便于取水的饮水点。安装位置的选择以原有自来水管道为准,同时考虑饮水是否方便、排污是否方便、用电是否方便、维护是否方便、冷天是否冻裂、与整体空间是否协调美观,还要避免小孩触碰。
1, the choice of location: commercial water purification devices are generally installed in the business, public places, easy to drink water point. Installation position of the selection to the original water pipeline, considering the drinking is convenient, sewage is convenient, with electricity is convenient and the maintenance is convenient, cold weather is cracking, and the whole space is harmonious and beautiful, but also to avoid the child touch.
2、 配件的选择:一般终端自来水管道为6分或4分塑胶管或金属管,而净水器一般用4分或2分管。1寸管、6分管、4分管为通用管件,也有互变的接头,球阀,在建材或五金店都可买到。2分管是非标管件,与之相配套的有4变2接头,2分直通、2分弯通、2分三通,2分螺母,2分管塞,2分龙头等配件,SUS4分三通(中间2分口)、SUS2分球阀、胶塞、胶钉等。我公司对非标配件都有配送。
2, the choice of accessories: the general terminal tap water pipe for 6 or 4 plastic rubber hose or metal pipe, and water purifier generally 4 or 2 in charge of. 1 inch pipe, 6, 4 in general is in charge of pipe fittings, are Enantiotropic joints, ball valves, or hardware store in the building materials are available. 2 in charge is non-standard fittings, matched with four variable joint 2, 2 minutes straight, bending, two three links, nut, 2 in charge of plug, 2 points leading parts. SUS4 divided into three-way (middle 2 points), sus2 ball valve, a rubber plug, a rubber nail. My company has distribution of non-standard accessories.
3、 安装工具的准备:安装净水器,一般需要冲击钻打孔(钻头配6分或8分)或开孔(开孔器选φ11-16mm),以便将直饮机或水龙头固定;生胶带可以避免接头漏水;专用胶便于塑胶接头的连接;十字螺丝刀、一字螺丝刀、电笔、扳手、剪刀、小刀,管钳等工具都是常用的安装工具。
3, installation tools preparation: install the water purifier, the general need to impact drill holes (bit 6 or 8 points) or opening (open hole packer phi 11-16mm), so that the straight drink machine tap or fixed; tape can avoid leaking joints; special glue for the connection between the plastic connectors; cross screwdriver, screwdriver, pencil, wrench, scissors, knives, forceps and other tools are commonly used in the installation tool.
4、 商业净水器安装流程规范:
4, installation process specification:
(1)、在选定的位置打孔或固定净水器。孔要圆滑,深度、孔距要准确,孔围不能有裂痕或缺口、毛边。
(1) perforated or fixed water purifier at selected locations. Hole depth, hole spacing should be smooth, accurate, no cracks or holes around the edges, gap.
(2)、与自来水管连接。先关闭自来水总阀,连接净水器,接口要缠生胶带,不能漏水。
(2) connected to the tap water pipe. First close the total water valve, connect water purifier, the interface should be wrapped around the tape, can not leak.
(3)、连接浓水排放口。纯水机可将排污管直接放入排污管道,端口要留一定空间,以避免污水倒流入净水器,防止排污口“虹吸”现象产生;如将净水器排污管直接放入排污管道,应在排污管端装一球阀,不定时打开可起到排污作用;也可将排污管直接与原先自来水龙头相连。排污管与净水器排污口一定要接好,不能漏水。
(3) the discharge of concentrated water. Pure water machine can be sewage pipe directly into the sewage pipes, port to leave certain space, in order to avoid sewage flowed into the water purifier, to prevent sewage outfall siphon phenomenon; such as net water heater drain pipe directly into the sewage pipes, should be in the sewage pipe is arranged at the end of a ball valve, from time to time open to blowdown effect; can also be discharge tube is connected directly with the original water tap. Sewage pipe and water outlet must be connected to the water heater, can not leak.
(4)、连接净化水出口与净化水龙头。如流量大于500升,可直接用4分管与通用龙头;如流量小于500升,可选择用4变2接头与净化水出口连接,通过2分白色PE管与2分水龙头连接。连接2分管时,先将管端口切平,再套上螺帽,然后把管塞插入PE管,插紧,将PE管超出螺帽1CM左右插入接头拧紧即可。
(4) connect the water outlet of the purified water and the tap. Such as flow is greater than 500 litres, can be directly used 4 charge and a general tap; such as flow is less than 500 litres, can choose 4 2 joint and purifying water outlet connection, by two white PE pipe and 2 faucet connection. 2 in charge of connection, the first tube port cut flat, and then set the nut, then the pipe plug is inserted into the PE pipe, in tight, will PE pipe beyond nut 1cm about plug in connector can be tightened.
(5)、安装水龙头:如果要将水龙头装在水槽上,不锈钢水槽可用开孔器开孔,如果要将水龙头固定在墙面,可用直角龙头挂片将水龙头固定在墙面。接头接法与(4)相同,固定部分要拧紧,不能有晃动。
(5), install the faucet: if you want to be installed in the water tank, stainless steel water tank can be used to open the hole, if you want to fix the faucet in the wall, the right angle faucet can be fixed on the wall. Joint method and (4) the same, the fixed part should be tightened, can not shake.
(6)、打开总进水球阀,对净水机进行调试(调试步骤详见维护与保养),观察接头是否漏水,观察期最少2个小时,可在净水机下放一块干净的干毛巾,检查是否有渗水现象。
(6), open a total water inlet ball valve, debugging debugging steps detailed in maintenance and maintenance), observe the joint is leaking, an observation period of at least 2 hours, in the water purifier decentralization a clean dry towel on the water purifier, check whether there is water seepage phenomenon.
5、商业净水器与饮水机连接规范:
5, water purifier and drinking machine connection specification:
安装固定好净水机后,将净化水出口与相关管线相连,将管线另一端直接接入小连通上盖进水端口,接法与(4)相同,再将小连通内液位控制浮球拧到中心位置,盖好小联通上盖,将小联通直接平稳放在饮水机上即可。如需要多接几个饮水点,只需在连接管线上接三通即可。
After the installation of fixed water purifying machine, will purify water outlet and pipeline connected. At the other end of the pipeline is directly connected with the connected cover inlet port, connection and (4) same minor communicates with the inner level control floating ball screw to the center position, cover connected small cover, the small Unicom direct smooth put on the drinking water machine can be. If you need more than a few drinking water points, only the connection pipe can be connected to three links.
6、 净水器安装完成,随时回访,7天之内要上门维护查看,指导客户使用维护方法。
6, water purification device installation is complete, at any time a return visit, within 7 days to check the site to guide customers to use the maintenance method.
商业净水器的安装要横平竖直,不能晃动,管线要拉直,远距离管线要用专业固钉稳固。整体要美观。
The water purifier is installed to horizontal and vertical pipelines can not shake, to straighten, long-distance pipeline to use solid solid professional nail. Overall to beautiful.